Atmel C51 Manuel Page 54
- Page / 116
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
The 8051 Instruction Set
Atmel 8051 Microcontrollers Hardware Manual 1-52
4316E–8051–01/07
1.14.36 ORL C,<src-bit>
ORL A,#data
Bytes: 2
Cycles: 1
Encoding: 0 1 0 0 0 1 0 0 immediate data
Operation: ORL
(A) ← (A)
∨
#data
ORL direct,A
Bytes: 2
Cycles: 1
Encoding: 0 1 0 0 0 0 1 0 direct address
Operation: ORL
(direct) ← (direct)
∨
(A)
ORL direct,#data
Bytes: 3
Cycles: 2
Encoding: 0 1 0 0 0 0 1 1 direct addr. immediate data
Operation: ORL
(direct) ← (direct)
∨
#data
Function: Logical-OR for bit variables
Description: Set the carry flag if the Boolean value is a logical 1; leave the carry in its current state otherwise. A slash ( / )
preceding the operand in the assembly language indicates that the logical complement of the addressed bit is
used as the source value, but the source bit itself is not affected. No other flags are affected.
Example: Set the carry flag if and only if P1.0 = 1, ACC. 7 = 1, or OV = 0:
MOV C,P1.0 ;LOAD CARRY WITH INPUT PIN P10
ORL C,ACC.7 ;OR CARRY WITH THE ACC. BIT 7
ORL C,/OV ;OR CARRY WITH THE INVERSE OF OV.
ORL C,bit
Bytes: 2
Cycles: 2
Encoding: 0 1 1 1 0 0 1 0 bit address
Operation: ORL
(C) ← (C)
∨
(bit)
ORL C,/bit
Bytes: 2
- Atmel 8051 Microcontrollers 1
- Hardware Manual 1
- Table of Contents 2
- Section 1 3
- 1.2 Addressing 4
- 1.3 Arithmetic 6
- 1.4 Logical 7
- 1.5 Data Transfers 8
- The 8051 Instruction Set 10
- 1.6 External RAM 11
- 1.7 Lookup Tables 11
- 1.8 Boolean 12
- Instructions 12
- C= bit1 XRL bit2 13
- MOV C, bit1 13
- JNB bit2, OVER 13
- OVER: (continue) 13
- 1.9 Jump 14
- 1.10 Read-Modify 16
- Write Instruction 16
- Features 16
- 1.11 Instruction Set 17
- 1.12 Instructions That 21
- Affect Flag 21
- Settings 21
- 1.13 Instruction Table 22
- 1.14 Instruction Definitions 25
- 1.14.2 ADD A,<src-byte> 26
- ADD A,direct 26
- ADD A,@R 26
- ADD A,#data 26
- ADDC A,R 27
- ADDC A,direct 27
- ADDC A,@R 27
- ADDC A,#data 27
- 1.14.4 AJMPaddr11 28
- ANL A,R 29
- ANL A,direct 29
- ANL A,@R 29
- 1.14.6 ANLC,<src-bit> 30
- ANL A,#data 30
- ANL direct,A 30
- ANL direct,#data 30
- ANL C,bit 30
- 1.14.7 CJNE <dest 31
- ANL C,/bit 31
- CJNE A,direct,rel 31
- CJNE A,#data,rel 32
- ,#data,rel 32
- CJNE @R 32
- ,data,rel 32
- 1.14.8 CLR A 33
- 1.14.9 CLR bit 33
- CLR bit 33
- 1.14.10 CPL A 34
- 1.14.11 CPL bit 34
- CPL bit 34
- 1.14.12 DA A 35
- 1.14.13 DECbyte 36
- DEC direct 36
- 1.14.14 DIVAB 37
- DJNZ direct,rel 38
- 1.14.16 INC<byte> 39
- INC direct 39
- 1.14.17 INC DPTR 40
- 1.14.18 JB blt,rel 40
- 1.14.19 JBC bit,rel 41
- 1.14.20 JC rel 41
- 1.14.21 JMP @A+DPTR 42
- 1.14.22 JNB bit,rel 42
- 1.14.23 JNC rel 43
- 1.14.24 JNZ rel 43
- 1.14.25 JZ rel 44
- 1.14.26 LCALLaddr16 44
- 1.14.27 LJMPaddr16 45
- 1.14.28 MOV <dest 45
- MOV A,R 45
- 4316E–8051–01/07 46
- 1.14.30 MOV DPTR,#data16 49
- 1.14.31 MOVC A,@A+ 49
- <base-reg> 49
- 1.14.32 MOVX <dest 50
- MOVC A,@A+DPTR 50
- MOVC A,@A+PC 50
- MOVX A,@R 50
- 1.14.33 MUL AB 51
- MOVX A,@DPTR 51
- MOVX @DPTR,A 51
- 1.14.34 NOP 52
- <src-byte> 53
- ORL A,direct 53
- ORL A,@R 53
- 1.14.35 ORL<dest-byte> 53
- 1.14.37 POP direct 56
- 1.14.38 PUSH direct 56
- 1.14.39 RET 57
- 1.14.40 RETI 57
- 1.14.41 RL A 58
- 1.14.42 RLC A 58
- 1.14.43 RR A 59
- 1.14.44 RRC A 59
- 1.14.45 SETB<bit> 60
- 1.14.46 SJMP rel 60
- SETB bit 60
- SUBB A,R 61
- SUBB A,direct 61
- SUBB A,@R 61
- 1.14.48 SWAP A 62
- 1.14.49 XCH A,<byte> 62
- SUBB A,#data 62
- XCH A,R 62
- XCH A,direct 62
- 1.14.50 XCHD A,@R 63
- XCH A,@R 63
- 1.14.51 XRL <dest 64
- XRL A,R 64
- XRL A,direct 64
- XRL A,@R 64
- XRL A,@#data 65
- XRL direct,A 65
- Section 2 66
- Note: (*)For Timer 2 only 67
- 2.2 Special Function 68
- Registers 68
- 2.3 Oscillator and 70
- Clock Circuit 70
- 2.4 CPU Timing 71
- 2.5 Port Structures 73
- 2.6 Accessing 77
- External Memory 77
- 2.7 PSEN 78
- Reset Value = XXXX XX00b 80
- Table 2-2. AUXR Register 80
- 2.9 Timer/Counters 81
- 2.10 Timer 0 82
- 2.11 Timer 1 84
- 2.12 Timer 2 89
- Timer 2 Control Register 92
- 2.13 Serial Interface 94
- Baud Rate Selection for 97
- UART for Mode 1 and 3 97
- Common Features Description 100
- 2.14 Framing Error 104
- Detection 104
- 2.15 Automatic 105
- Address 105
- Recognition 105
- UART Registers 108
- Reset Value = 0000 0000b 110
- Bit addressable 110
- Table 2-24. T2CON Register 110
- 2.16 Interrupts 112
- Regional Headquarters 116
Produits connexes et manuels pour Non Atmel C51
Non Atmel ATEVK525 Guide de l'utilisateur
(30 pages)
(30 pages)
Non Atmel REB233-XPRO Guide de l'utilisateur
(18 pages)
(18 pages)
Non Atmel REB233-XPRO Manuel d'utilisateur
(51 pages)
(51 pages)
Non Atmel AVR XMEGA 8/16-bit High Performance Low Power Flash Microcontrollers Fiche technique
(145 pages)
(145 pages)
Non Atmel AT91SAM7L-STK Manuel d'utilisateur
(35 pages)
(35 pages)
Non Atmel ATmega88PA Fiche technique
(39 pages)
(39 pages)
Non Atmel AT91SAM7L-STK Manuel d'utilisateur
(24 pages)
(24 pages)
Non Atmel REB233-XPRO Manuel d'utilisateur
(10 pages)
(10 pages)
Non Atmel AVR XMEGA 8/16-bit High Performance Low Power Flash Microcontrollers Manuel d'utilisateur
(18 pages)
(18 pages)
Non Atmel C51 Fiche technique
(21 pages)
(21 pages)
Non Atmel C51 Fiche technique
(127 pages)
(127 pages)
Non Atmel ATAK2270 Manuel d'utilisateur
(4 pages)
(4 pages)
Non Atmel ATAK2270 Manuel d'utilisateur
(5 pages)
(5 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels