Wireless LAN Access Point EW-7205AP User’s Manual
Wireless LAN Access Point Configuration 8 You can use the Get, Modify and Set buttons to configure the parameters for the Wireless LAN Access Point
Wireless LAN Access Point Configuration 9The parameters for the Wireless LAN Access Point are described below: Parameters Description MAC Address Th
Wireless LAN Access Point Configuration 10 Parameters Description Auto Rate Fall Back Select Enable or Disable. When this is enabled, the wireless ne
Wireless LAN Access Point Configuration 11 Parameters/Buttons Description Authentication Type Defines the Access Point’s authentication type. Only th
Wireless LAN Access Point Configuration 12 Parameters/Buttons Description Operational Mode Sets this Access Point to following operational mode. • Ac
Wireless LAN Access Point Configuration 13 Parameters/Buttons Description SNMP Traps Enabled/Disabled SNMP traps which are messages indicating that a
Wireless LAN Access Point Configuration 14 3.2 Access Point SNMP Manager 3.2.1 How to Install the SNMP Manager Step 1: Insert the Setup CD and run
Wireless LAN Access Point Configuration 15 Step 3: The Choose Destination Location screen will show you the default destination chosen by the progr
Wireless LAN Access Point Configuration 16 Step 4: In this frame you will find where the program will be installed. If you want to change the progr
Wireless LAN Access Point Configuration 17 Step 5: All the settings of this installation will be shown in the following screen. Click Back to change
Table of Contents Chapter 1 Introduction... 1 1.1 Package Contents ...
Wireless LAN Access Point Configuration 18 3.2.2 Using the SNMP Manager Before using the SNMP Manager to configure the Access Point, verify the Et
Wireless LAN Access Point Configuration 19 3.2.2.1 Connecting to the Access Point Connect to the Access Point Pull down the File menu and select
Wireless LAN Access Point Configuration 20 Find Access Point Pull down the File menu and select the Connect to Access Point submenu. This submenu
Wireless LAN Access Point Configuration 21 Refresh If you want to get the original setting on the Access Point, pull down the File menu and select
Wireless LAN Access Point Configuration 22 Privacy Options Pull down the Setup menu and select the Privacy Options from the Wireless LAN submenu.
Wireless LAN Access Point Configuration 23 Access Point Name Fill in a user-friendly name for the Access Point. ESSID This is an up to 32 charact
Wireless LAN Access Point Configuration 24 Auto Rate Fall Back When this is enabled the transmission rate is the optimum rate. In case of obstacles
Wireless LAN Access Point Configuration 25 Modify Authorized MAC Address Pull down the Setup menu and select the Authorized Mac Address from the
Wireless LAN Access Point Configuration 26 Authorization Table Enable If checked, only devices with MAC Addresses in the Authorization Table can co
Wireless LAN Access Point Configuration 27 If you want to view additional information for every Trap Message, you could pull down the Traps menu and
Introduction 1Chapter 1 Introduction This Wireless LAN Access Point provides a flexible way for users to configure their network by eliminating LAN
Wireless LAN Access Point Configuration 28 Reset Device You can reset the Access Point. This action takes place after a user makes configuration ch
Wireless LAN Access Point Configuration 29 Wireless Statistics Pull down the Info menu and select the Wireless Statistics submenu to view the repor
Wireless LAN Access Point Firmware Upgrade 30Chapter 4 Wireless LAN Access Point Firmware Upgrade Two software tools are provided to upgrade Access
Wireless LAN Access Point Firmware Upgrade 31 4.2 TFTP Client 4.2.1 How to Install the TFTP Client Please run the program setup.exe which you will
Wireless LAN Access Point Firmware Upgrade 32
Troubleshooting 33Chapter 5 Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of
Troubleshooting 34 7. Can data be intercepted while transmitting through the air? WLAN features two-fold protection in security. On the hardware sid
Introduction 2 Plug-and-play installation. Desktop and wall mountable design. 1.3 Specifications Standards: IEEE 802.3 and IEEE 802.3u (Wir
Introduction 3 Receive Sensitivity: -80 dBm @FER=8% , 11 Mbps. -83 dBm @FER=8% , 5.5 Mbps -86 dBm @FER=8%, 1 Mbps Dimension: 190(H) x 65(W)
Introduction 4 LED Color Status Description Lit Power is supplied. Power Green Off No Power. Lit A valid link is established. Flash Data pack
Introduction 5 USB Port The USB port which connects to an USB-ready PC is used to configure the Access Point. To work with USB port, the PC must be
Wireless LAN Access Point Connection 6Chapter 2 Wireless LAN Access Point Connection 1. Locate an optimum location for the Wireless LAN Access Poin
Wireless LAN Access Point Configuration 7Chapter 3 Wireless LAN Access Point Configuration Two software tools are provided to configure the Access P
Commentaires sur ces manuels